Window AC on a 15 or 20 Amp Circuit and When It Needs Its Own

By BuildSolver11 min read

Calculations follow ACCA Manual J/S/D procedures and ASHRAE standards.

On this page

A plug-in window air conditioner can be marked at up to 80% of a branch circuit it has to itself, which is 12 A on a 15 A circuit and 16 A on a 20 A circuit, under NEC 440.62(B). If the same circuit also feeds lights or other receptacles, 440.62(C) drops the limit to 50%, so 7.5 A on 15 A and 10 A on 20 A. In the window line we checked, every 115 V unit from 10,000 BTU up is over the shared 15 A limit.

This guide works those four limits against a real seven-model window line from one maker's spec sheet, then runs the 12,000 BTU unit from an r/AskElectricians question on a shared 15 A and a shared 20 A circuit. If the nameplate is gone, our free AC amps and watts calculator turns capacity and efficiency into running watts and amps, and the last section shows how far that estimate can sit from the plate.

What does NEC 440.62 allow on a 15 or 20 amp circuit?

Two limits, both checked against the marked current on the nameplate. Alone on its circuit, a cord-and-plug room air conditioner may be marked at up to 80% of the circuit rating. With lighting outlets, other appliances or general-use receptacles on the same circuit, the cap is 50%. An interlock that keeps the other outlets dead while the unit runs puts it back at 80%.

NEC 2008 § 440.62(B)
"The total marked rating of a cord-and-attachment-plug-connected room air conditioner shall not exceed 80 percent of the rating of a branch circuit where no other loads are supplied." - NFPA 70, as reproduced by Solar365, solar365.com

Part VII of Article 440 covers window, console and in-wall units that sit in the room they cool, rated 250 V or less, single phase (440.60). The unit counts as a single motor unit when it's cord-and-plug connected, rated 40 A or less, shows one total rated-load current on its nameplate and sits on a breaker no larger than the wire or the receptacle allows (440.62(A)). Multimotor and combination-load air-conditioning equipment falls under a different rule, which the 2024 IRC states as E3702.12. Its wire ampacity is at least the minimum circuit ampacity marked on the unit, and its breaker is the size and type marked on it.

CircuitUnit alone on the circuit, 80% (440.62(B))Lights or receptacles also on it, 50% (440.62(C))
15 A12 A7.5 A
20 A16 A10 A

The quote above is from the 2008 NEC. The 2021 and 2024 International Residential Code carry the 80% and 50% limits as E3702.12 (2021) and E3702.13 (2024), with 440.62 cited in brackets, though their 50% case names lighting or other appliances and doesn't list general-use receptacles. An EC&M walkthrough of Part VII by Mark Lamendola, dated April 3, 2023, gives the same 80% and 50% figures. Check the edition your inspector enforces.

Which window units fit which circuit?

On one maker's 115 V line, every model through 14,500 BTU fits a 15 A circuit it has alone, since the largest is listed at 11.8 A. On a shared 15 A circuit only the 6,000 and 8,000 BTU units fit, and on a shared 20 A circuit everything up to 12,000 BTU does. The 25,000 BTU 208/230 V model needs a 20 A circuit.

The figures below come from the spec sheet for HD Supply's Seasons window line, revision August 20, 2021, which lists each model's current and NEMA plug. For the two 208/230 V models we used the 208 V current, the higher of the two, and checked them only alone on their circuit. 440.62 reads the total marked rating on the unit's nameplate, so confirm each figure on the label.

Model, BTU/hVolts, plugCurrent on spec sheet15 A alone, 12 A15 A shared, 7.5 A20 A alone, 16 A20 A shared, 10 A
SW06R1, 6,000115 V, 5-15P4.5 AFitsFitsFitsFits
SW08R1, 8,000115 V, 5-15P5.9 AFitsFitsFitsFits
SW10R1, 10,000115 V, 5-15P8.03 AFitsOverFitsFits
SW12R1, 12,000115 V, 5-15P9.72 AFitsOverFitsFits
SW15R1, 14,500115 V, 5-15P11.8 AFitsOverFitsOver
SW18R2, 18,000230/208 V, 6-15P7.2/7.6 AFitsNot checkedFitsNot checked
SW25R2, 25,000230/208 V, 6-20P12.2/13 AOverNot checkedFitsNot checked

These cells compare current only. A receptacle also has to be rated for the circuit and take the unit's plug, which the circuit section below covers.

The 14,500 BTU SW15R1 is the tight one. At its listed 11.8 A it clears 12 A by 0.2 A on a 15 A circuit of its own, yet it's over 10 A on a 20 A circuit shared with a bedroom's receptacles.

The SW25R2 is over 12 A even at 230 V, so a 15 A, 240 V circuit is out, and its 6-20P plug matches the 20 A circuit it needs. Other brands mark different currents for the same BTU rating.

Can the 12,000 BTU unit from the thread share a circuit?

Not a shared 15 A circuit, since 9.3 A is over the 7.5 A that 440.62(C) allows. On a shared 20 A circuit the 9.3 A figure fits under 10 A and the 10.5 A maximum doesn't. The poster says the unit itself calls for a single outlet circuit, and a 15 A circuit with nothing else on it takes either figure under its 12 A cap.

The poster rents an upstairs two-bedroom apartment with no central air and bought a 12,000 BTU Denali Aire window unit. They gave its label as 115 V, 9.3 A and 10.5 A maximum, and said it needs a single outlet circuit. They didn't know which circuit fed the window they wanted, or what else was on it.

Here are the three cases, using the figures as the poster typed them.

Circuit the unit lands onLimit9.3 A10.5 A
15 A, shared with other receptacles or lights7.5 AOverOver
20 A, shared with other receptacles or lights10 AFitsOver
15 A or 20 A, nothing else on it12 A or 16 AFitsFits

The code check alone lets the 9.3 A figure onto a shared 20 A circuit, but the poster says the unit calls for a single outlet circuit, which is stricter, so read that instruction on the unit before counting on a shared circuit. We haven't seen the label. Only the label says which of the two numbers is the marked rating. A 10,000 BTU unit, the size the poster considered next, is listed at 8.03 A on the Seasons sheet above, still over the 7.5 A of a shared 15 A circuit.

What does a new circuit for a window unit need?

A 15 A breaker on 14 AWG copper covers units marked up to 12 A, and a 20 A breaker on 12 AWG covers up to 16 A. The receptacle has to be rated at least as high as the breaker, so a 20 A circuit gets a 20 A receptacle. The cord can't run more than 10 ft on a 120 V unit or 6 ft on a 208 or 240 V unit, so the receptacle goes near the window.

  1. Read the marked current, voltage and plug type off the unit's label. On the Seasons sheet the 115 V models use a 5-15P plug and the 208/230 V models a 6-15P or 6-20P.
  2. Pick the circuit from the 80% limit. 12 A or less fits 15 A, and 16 A or less fits 20 A.
  3. Size the wire to the breaker. The 2024 IRC Table E3705.5.3, which restates NEC 240.4(D), caps 14 AWG copper at 15 A and 12 AWG copper at 20 A.
  4. Pick the receptacle to match the breaker. Under 210.21(B)(1), a single receptacle on an individual branch circuit has to be rated at least as high as the breaker, and for a room unit 440.62(A)(4) keeps the breaker no larger than the receptacle rating. A 20 A circuit gets a 20 A receptacle that takes the unit's plug.
  5. Place it within reach of the cord. 440.64 caps the cord at 10 ft for a 120 V unit and 6 ft for 208 or 240 V, and Lamendola's EC&M article calls an extension cord a clear violation of the rule's intent. The 115 V Seasons models have 6-1/2 ft cords, inside the 10 ft limit. The sheet lists the same 6-1/2 ft for its two 208/230 V models, over the 6 ft in the 2008 text, so measure the cord on the unit you're installing.
  6. Use the plug as the disconnect only where 440.63 allows it. That takes controls that are readily accessible and within 6 ft of the floor, or an approved manually operable disconnect in a readily accessible spot within sight of the unit.

Leave the cord's protection device in place. Under 440.65 the cord on a single-phase room unit carries a factory leakage-current detector-interrupter (LCDI) or AFCI in the plug or within 12 in. of it, and the 2023 EC&M article also lists a heat-detecting circuit interrupter (HDCI). Our AC breaker size calculator doesn't cover cord-and-plug room units. It sizes condensers, heat pumps and mini splits from the compressor RLA and fan amps on the nameplate, and uses the plate's MCA and maximum breaker when you also enter them.

How close can you get without the nameplate?

Divide the rated BTU/h by the efficiency in BTU per watt-hour to get watts, then by the voltage for amps. It assumes a power factor of 1, so it usually lands under the plate. The SW12R1's sheet gives 12,000 BTU/h and 1,000 W, an efficiency of 12.0, which works out to 8.7 A at 115 V, about 1 A under the 9.72 A it lists.

In the running mode of the AC amps and watts calculator, enter the capacity, put the efficiency in the EER2 field, pick 115 V and leave the power factor blank to get that estimate. With a power factor of 0.9, our assumption, the page gives 9.7 A. That's close to the sheet. The same 0.9 would put the SW15R1 at 12.4 A against its listed 11.8 A, so one guess lands close on the SW12R1 and 0.6 A high on the SW15R1.

The power factor the Seasons sheet implies for its five 115 V models, watts over 115 V times amps, runs from 0.89 for the SW12R1 to about 1.00 for the SW10R1, our arithmetic. For the SW10R1 the estimate at a power factor of 1 is 8.0 A, level with the 8.03 A listed, so it isn't always under the plate. The calculator notes that window units are rated in CEER, not EER2, and that the capacity and efficiency you enter must come from the same rating. If the label's gone, call the manufacturer for the marked current before you pick the circuit.

If the room is running a high bill, our guide to checking whether an AC uses too much electricity covers the watts side. For the circuit, run the unit's capacity through the AC amps and watts calculator for a first number, then compare the marked current on the label with the 12, 7.5, 16 and 10 A limits before you plug it in or pull a new circuit.

Sources

  • NFPA 70, National Electrical Code 2008, Article 440 Part VII, Sections 440.60 to 440.65, as reproduced by Solar365: 440.60 to 440.63 and 440.63 to 440.65
  • International Code Council, 2021 and 2024 International Residential Code, Chapter 37, Sections E3702.12 (2021), E3702.12 and E3702.13 (2024) and Table E3705.5.3: 2021 and 2024
  • Mark Lamendola, EC&M, NEC air-conditioning and refrigerating equipment, part 7, April 3, 2023: ecmweb.com
  • EC&M, Branch circuits, part one, April 1, 2007, on 210.21(B): ecmweb.com
  • HD Supply, Seasons window air conditioner cooling only, specification sheet, rev. August 20, 2021: hdsupplysolutions.com
  • Source question, r/AskElectricians, "Bigger window ac on a dedicated circuit?": reddit.com

For estimation purposes only. A licensed electrician sizes, installs and signs off any new circuit under the code and amendments your jurisdiction has adopted.

Related guides

Calculators for this topic

Run your own numbers in the free Manual J load calculator.