Maintained by BuildSolver · Updated
Calculator · Electrical
Ohm's law calculator
Voltage equals current times resistance, and power equals voltage times current. Enter any two of volts, amps, ohms and watts and this page gives the other two. An 18 V battery across a 3 ohm lamp drives 6 A and 108 W; on 36 V the same lamp takes 12 A and 432 W. It holds for direct current and for a resistive load on single-phase alternating current, such as a heating element, where the power factor is 1. For a motor or a power supply on AC, use the kW to amps calculator; for the volts lost along a wire, the voltage drop calculator.
- Choose the pair from the list: voltage and resistance, voltage and current, voltage and power, current and resistance, current and power, or resistance and power.
- Convert milliamps to amps (divide by 1,000), kilohms to ohms (multiply by 1,000) and kilowatts to watts (multiply by 1,000) before typing them in.
- The result shows the two unknowns with the formula and the numbers behind each, and a check that all three power formulas agree.
Example result for the default inputs
Voltage 18 V and resistance 3 ohm.
Current
6 A
Power
108 W
| Current | V / R = 18 V / 3 ohm = 6 A |
|---|---|
| Power | V^2 / R = 18^2 / 3 ohm = 108 W |
| Check | V x I = 108 W, I^2 x R = 108 W, V^2 / R = 108 W. All three agree. |
| Heat | All of the power in a resistance ends up as heat. Every watt. The part, the wire or the element has its own watt rating; keep the result under it with margin. |
| Where this holds | Direct current, or alternating current into a resistive load such as a heating element, with RMS values and a power factor of 1. For a motor or a power supply on AC the power factor lowers the real power, and the kW to amps calculator takes it into account. |
For estimation purposes only. Consult a licensed engineer for final designs.
Sign up with your email. Back on this page in the same browser, your inputs are filled in. No card.
Free without signup
How the four quantities connect
Ohm's law ties three quantities together: the voltage across a resistance equals the current through it times the resistance. Power, the rate at which that resistance turns electrical energy into heat, is the voltage times the current. Put the two together and each of the four quantities can be found from any two of the others. Every formula below is the same pair of relations rearranged.
- Voltage
V = I x RA 6 A current through 3 ohm drops 18 V, the All About Circuits lamp. Also V = P / I and V = sqrt(P x R).- Current
I = V / R36 V across 3 ohm is 12 A, twice the 6 A at 18 V. Also I = P / V and I = sqrt(P / R).- Resistance
R = V / IThe OpenStax headlight at 12 V and 2.5 A is 4.8 ohm when hot. Also R = V^2 / P and R = P / I^2.- Power from V and I
P = V x I12 V x 2.5 A is 30 W, the headlight figure in OpenStax Example 20.7.- Power from I and R
P = I^2 x R6 A through 3 ohm is 108 W. Double the current and the power is four times as much.- Power from V and R
P = V^2 / R36 V across 3 ohm is 432 W, four times the 108 W at 18 V.- From power and resistance
V = sqrt(P x R), I = sqrt(P / R)The cold headlight, 0.35 ohm at 12 V, is 411.4 W and 34.29 A; OpenStax prints 411 W and 34.3 A.
Eight resistances through the same formulas
The first four rows are the textbook examples: the All About Circuits lamp on 18 and 36 V, and the OpenStax headlight, hot at 30 W and cold at 411.4 W and 34.29 A. Two rows turn a heater rating into a current and a resistance. Then come small resistors, where the watt rating of the part matters as much as the ohms.
| Load | Known | Volts, V | Amps, A | Ohms | Watts, W |
|---|---|---|---|---|---|
| Lamp on an 18 V battery | 18 V, 3 ohm | 18 | 6 | 3 | 108 |
| Same lamp on 36 V | 36 V, 3 ohm | 36 | 12 | 3 | 432 |
| 12 V headlight, hot | 12 V, 2.5 A | 12 | 2.5 | 4.8 | 30 |
| 12 V headlight, cold | 12 V, 0.35 ohm | 12 | 34.29 | 0.35 | 411.4 |
| 1,500 W space heater | 120 V, 1,500 W | 120 | 12.5 | 9.6 | 1,500 |
| 4,500 W water heater element | 240 V, 4,500 W | 240 | 18.75 | 12.8 | 4,500 |
| 1,000 ohm resistor | 10 mA (0.01 A), 1,000 ohm | 10 | 0.01 | 1,000 | 0.1 |
| 100 ohm resistor on 12 V | 12 V, 100 ohm | 12 | 0.12 | 100 | 1.44 |
Power grows with the square. On a fixed resistance, double the voltage or the current and the power is four times as much, which is why a modest rise in supply voltage heats a resistor or an element far more than it seems it should.
Standards and data sources
- All About Circuits, Lessons in Electric Circuits, Volume I (DC), Chapter 2, Ohm's Law (voltage, current and resistance) - E = IR, I = E / R and R = E / I, the relations behind the first three formulas on this page.
- All About Circuits, Lessons in Electric Circuits, Volume I (DC), Chapter 2, Calculating Electric Power - P = I^2 R, P = I E and P = E^2 / R, and the worked lamp example this page opens on: 18 V across 3 ohm is 6 A and 108 W, and 36 V is 12 A and 432 W.
- OpenStax, College Physics 2e, section 20.4 Electric Power and Energy (Equations 20.28 to 20.30, Example 20.7) - P = IV, P = V^2 / R and P = I^2 R, and the headlight example tested here: 12.0 V at 2.50 A is 30.0 W, and cold at 0.350 ohm it is 411 W and 34.3 A.
Limitations of this calculator
- This page does arithmetic on two numbers you supply. It does not design a circuit, size a wire or a breaker, or replace the work of a licensed electrician under the permit and the inspection of the local authority having jurisdiction (AHJ).
- It holds for direct current, and for alternating current into a purely resistive load such as a heating element or an incandescent lamp, with RMS values and a power factor of 1. A motor, a compressor or a power supply on AC has a power factor below 1, and V x I is then apparent power, not the real power. Use the kW to amps calculator for those loads.
- The result is for a single resistance. It does not add resistors in series or in parallel, and it does not follow a current through a branched circuit; work each resistance on its own, or reduce the network first.
- A real resistance moves. A tungsten filament has a resistance that rises steeply with temperature, so its cold value is a fraction of its hot value. A nichrome heating element rises only by a few percent, and a carbon-film resistor has a tolerance of 1 to 5 percent. Enter the value at the operating condition.
- A heating element is close to a fixed resistance, so its power depends on the voltage it actually sees. A 240 V rating does not hold on a 208 V supply, and a supply that sags under load delivers less than its label.
- The power is heat. The page does not check a resistor, a wire or an element against its own power rating; keep the result under that rating with margin.
- Entries are in volts, amps, ohms and watts. Convert milliamps, kilohms, megohms and kilowatts before entering them. Values outside 0.001 to 100,000 V, 0.001 to 100,000 A, 0.001 to 10,000,000 ohm and 0.001 to 100,000,000 W are not accepted.
- Resistance of a wire over a length, and the voltage lost along it, are not worked here. The voltage drop calculator does that with the conductor table.
Common mistakes with Ohm's law
- Entering milliamps as amps. A 1,000 ohm resistor carrying 10 mA is 0.01 A. It drops 10 V and makes 0.1 W. Typing 10 as the amps gives 10,000 V and 100,000 W, a million times the power. Convert first: mA / 1,000, kilohm x 1,000, kW x 1,000.
- Thinking that double the voltage is double the power. With the resistance fixed, doubling the voltage doubles the current and quadruples the power. The All About Circuits lamp makes 108 W at 18 V and 432 W at 36 V. The same square works downward: a drop of 13 percent in voltage takes about a quarter of the power off a heating element.
- Using a 240 V rating at 208 V. A 4,500 W, 240 V element is 12.8 ohm. On 208 V it draws 16.25 A and makes about 3,380 W. Dividing 4,500 W by 208 V instead gives 21.63 A, which is more than the element can draw. Take the resistance from the rating, then apply the voltage you have.
- Using a cold resistance for a running load. The OpenStax headlight measures 0.35 ohm cold and works out to 4.8 ohm hot. At 12 V it draws 34.29 A at the moment of switch-on and 2.5 A once warm, about 13.71 times as much. Incandescent lamps start at a current many times their running current, and motors do too, for a different reason: no back-EMF until they spin up.
- Applying P = V x I to an AC motor. For a resistive load, 1,000 W at 120 V is 8.333 A. For a motor or a power supply at a power factor of 0.8 the same 1,000 W draws 10.42 A, and V x I no longer gives the real power. This page assumes a power factor of 1; the kW to amps calculator takes the power factor in.
- Picking a resistor by resistance alone. A 100 ohm resistor on 12 V carries 0.12 A and has to shed 1.44 W. A common quarter-watt resistor would run far past its rating. Check the power, then choose a part rated well above it.
Common questions about Ohm's law and power
What is Ohm's law?
The voltage across a resistance equals the current through it times the resistance: V = I x R. Rearranged, I = V / R and R = V / I. An 18 V battery across a 3 ohm lamp drives 6 A, because 18 / 3 = 6. That is the whole law.
What are the formulas for electric power?
P = V x I, P = I^2 x R and P = V^2 / R. They are the same relation: put V = I x R into P = V x I and you get the other two. For the 18 V, 3 ohm lamp, 18 x 6, 6^2 x 3 and 18^2 / 3 are all 108 W.
How do you find resistance from watts and volts?
Square the voltage and divide by the watts: R = V^2 / P. A 1,500 W space heater on 120 V is 120^2 / 1,500 = 9.6 ohm, and a 4,500 W element on 240 V is 12.8 ohm.
How many amps does a 1,500 watt heater draw?
12.5 A on 120 V: 1,500 W / 120 V. A resistive heater has a power factor of 1. Nothing else is needed. A 4,500 W element on 240 V draws 18.75 A.
Why does doubling the voltage quadruple the power?
Because the current rises with the voltage and the power is the voltage times the current. With the resistance fixed, 36 V across 3 ohm is 12 A and 432 W, against 6 A and 108 W at 18 V: twice the current, four times the power.
Does Ohm's law work on AC?
Yes for a resistive load, with RMS voltage and current and a power factor of 1: heating elements, ovens and incandescent lamps. A motor, a compressor or a power supply has reactance, so the real power is the voltage times the current times the power factor. For those loads on single phase or three phase, use the kW to amps calculator.
How do you convert milliamps and kilohms?
Mind the prefix. Divide milliamps by 1,000 for amps: 10 mA is 0.01 A. Multiply kilohms by 1,000 for ohms: 4.7 kilohm is 4,700 ohm. Multiply kilowatts by 1,000 for watts. With 0.01 A through 1,000 ohm the drop is 10 V and the power 0.1 W.
Why is a cold bulb's resistance so low?
The resistance of a metal filament rises with temperature. OpenStax gives a headlight at 0.35 ohm cold, which on 12 V is 34.29 A and 411.4 W at switch-on. Hot it is 4.8 ohm and 30 W at 2.5 A.
Can I size a wire or a breaker from this?
No. This gives the current and the power of a resistance. The wire and the breaker depend on the conductor, the temperature, the length and the way the load runs; a continuous load is sized at 125 percent of its current. Take the current to the wire size calculator, and the length of the run to the voltage drop calculator.