Maintained by BuildSolver · Updated
Calculator · Roofing
Roofing shingle calculator
Enter the house size, the pitch, the overhangs and the waste, and this page gives the roof area, the squares to order and the bundles of shingles, starter strip and hip and ridge cap. A 40 x 30 ft gable at 6/12 with 12 in overhangs is 1,503 sq ft of roof, 16.53 squares with 10 percent waste, and 50 bundles at 3 per square, plus 2 bundles of starter and 2 of ridge cap. For the length of the rafters use the rafter length calculator; for the vents under the same roof, the attic ventilation calculator.
- Gable or hip, the outside wall length and width, and the pitch as rise per 12 in of run. On a gable the ridge runs parallel to the length.
- The horizontal eave overhang (and the rake overhang on a gable) widen the roof past the walls. Waste is your allowance; GAF and Owens Corning say to add 10 to 15 percent, more on a steep or cut-up roof.
- GAF Timberline HDZ or Owens Corning Duration load the bundles per square and the cap and starter coverage from the open data sheets. Pick other to type the figures from the label.
- The result gives the roof area, the squares to order, the bundles of shingles, and the bundles of starter strip and hip and ridge cap, each rounded up.
Example result for the default inputs
Gable roof, 40 x 30 ft, 6/12, eave 12 in, rake 12 in, waste 10 percent.
Shingle bundles
50 bundles
Roof area
1,503 sq ft
Squares to order
16.53 squares
Starter / cap bundles
2 / 2
| Pitch multiplier | sqrt(1 + (6 / 12)^2) = 1.1180 (6/12) |
|---|---|
| Run, ridge to drip edge | 30 / 2 + 1.00 = 16.00 ft level, 17.89 ft along the slope |
| Plan area with overhangs | 2 x 16.00 x 42.00 = 1,344 sq ft |
| Roof area | 1,344 x 1.1180 = 1,503 sq ft (15.03 squares) |
| Squares with waste | 15.03 x (1 + 10 / 100) = 16.53 squares |
| Shingle bundles | 16.53 x 3 bundles per square = 49.59, rounded up to 50 |
| Bundles at the maker's coverage | 1,653 sq ft / (98.4 / 3 = 32.8 sq ft per bundle), rounded up to 51 |
| Eave edge | 2 x 42.00 ft = 84.0 ft |
| Rake edge | 4 x 17.89 ft = 71.6 ft |
| Starter strip | 155.6 ft / 120.33 lin. ft. per bundle = 1.29, rounded up to 2 |
| Ridge | 42.00 ft along the ridge |
| Hip and ridge cap | 42.0 ft / 25 lin. ft. per bundle = 1.68, rounded up to 2 |
| Product figures used | GAF Timberline HDZ: 3 bundles per square; Seal-A-Ridge 25 lin. ft. and Pro-Start 120.33 lin. ft. per bundle |
- Material estimate for one rectangular roof of one pitch. Valleys, dormers, chimneys, skylights, an L-shaped plan, a second layer or a tear-off are not figured; work each rectangle on its own and add them.
- Waste is your allowance. GAF and Owens Corning say to add 10 to 15 percent for trim and waste, and more on a steep or cut-up roof. Starter and cap are counted at their exact length, with no cut loss added.
- Bundle counts and coverage per bundle change between lines and over time. Check the manufacturer's label on the bundle you buy.
- The makers state that 3 bundles cover 98.4 sq ft, not 100. At that coverage this roof needs 51 bundles, not 50. Raise the waste or order 51.
- The ridge is taken parallel to the length typed. For a gable over the width, swap length and width.
For estimation purposes only. Consult a licensed engineer for final designs.
Sign up with your email. Back on this page in the same browser, your inputs are filled in. No card.
Free without signup
How the shingle quantities are found
The page measures the roof surface of a simple rectangle from the footprint and the pitch, turns it into squares of 100 sq ft, adds your waste allowance and divides by the bundles per square. The starter strip and the hip and ridge cap are separate products bought by the linear foot, so they are measured along the edges and divided by what one bundle covers. Every package count is rounded up, never down.
- Pitch multiplier
k = sqrt(1 + (rise / 12)^2)It turns a level area into the sloped surface: Gable 4/12 1.0541, 6/12 1.1180, 8/12 1.2019, 12/12 1.4142. The same multiplier as the rafter length page.- Gable roof area
run = W / 2 + eave overhang; area = 2 x run x k x (L + 2 x rake overhang)A 40 x 30 ft house with 12 in overhangs has a run of 16.0 ft, a slope length of 17.9 ft and 1,344 sq ft of plan including the overhangs, so 1,503 sq ft of roof at 6/12. 1,000 sq ft of plan at 6/12 would be 1,118 sq ft.- Hip roof area
area = (long side + 2 x eave) x (short side + 2 x eave) x kThe same 40 x 30 ft house as a hip roof has the same 1,344 sq ft of plan with a 12 in eave all round, so 1,503 sq ft of roof. A hip roof has no rake overhang.- Squares and waste
squares = area / 100; to order = squares x (1 + waste / 100)1,503 sq ft is 15.03 squares, and 16.53 squares with 10 percent waste. One square is 100 sq ft of roof.- Shingle bundles
bundles = ceil(squares to order x bundles per square)16.53 x 3 = 49.59, so 50 bundles. GAF Timberline HDZ and Owens Corning Duration are both 3 bundles per square.- Starter strip
starter = eaves (+ rakes on a gable); bundles = ceil(starter / lin. ft. per bundle)Eaves 84.0 ft plus rakes 71.6 ft is 155.6 ft: 2 bundles of Pro-Start at 120.33 lin. ft. or 2 of Starter Strip Plus at 105.- Ridge and hip cap
gable: ridge = L + 2 x rake; hip: ridge = long - short side, hip = (W' / 2) x sqrt(2 + (rise / 12)^2) x 4The gable ridge is 42.0 ft: 2 bundles of Seal-A-Ridge at 25 lin. ft. or 3 of DecoRidge at 20. The hip roof has a 10.0 ft ridge and four hips of 24.0 ft, 106.0 ft of cap, 5 bundles of Seal-A-Ridge.
The same 40 x 30 ft house at common pitches
Each row is the 40 x 30 ft house with 12 in eave and rake overhangs and GAF Timberline HDZ figures, worked with the same function as the form. Gable rows use 10 percent waste and the hip row 15 percent. The shingles grow from 47 bundles at Gable 4/12 to 63 at Gable 12/12.
| Roof | Multiplier | Roof area | Squares to order | Shingle bundles | Cap, ft |
|---|---|---|---|---|---|
| Gable 4/12 | 1.0541 | 1,417 sq ft | 15.58 | 47 | 42.0 |
| Gable 6/12 | 1.1180 | 1,503 sq ft | 16.53 | 50 | 42.0 |
| Gable 8/12 | 1.2019 | 1,615 sq ft | 17.77 | 54 | 42.0 |
| Gable 10/12 | 1.3017 | 1,749 sq ft | 19.24 | 58 | 42.0 |
| Gable 12/12 | 1.4142 | 1,901 sq ft | 20.91 | 63 | 42.0 |
| Hip 6/12 | 1.1180 | 1,503 sq ft | 17.28 | 52 | 106.0 |
Order to the roof, not the footprint: the 1,200 sq ft footprint is 1,503 sq ft of roof at 6/12 with its overhangs. The hip roof needs 106.0 ft of cap, 96.0 ft of it in the four hips, against 42.0 ft for the gable ridge.
Standards and data sources
- GAF Timberline HDZ Shingles specification sheet (RESGN467HDZ) and installation instructions (RESTL622) - About 13 1/4 x 39 3/8 in shingles at 5 5/8 in exposure, 3 bundles and 64 pieces per square. The installation instructions: 3 bundles (1 bundle of 20 and 2 bundles of 22) cover 98.4 sq ft.
- GAF Residential Full Line Reference Guide (RESGN100), with the Pro-Start sell sheet (RESGN546) - Seal-A-Ridge hip and ridge: 12 in wide, 6 2/3 in exposure, 25 lin. ft. per bundle (its sell sheet RESHR112: 4 bundles cover 100 linear feet). Pro-Start starter strip: 120.33 lin. ft. per bundle, the same figure as the Pro-Start sell sheet and the installation instructions (RESGN853). The older GAF Pro Field Guide (RESGN103, version 2.1) prints 33 lin. ft. per Pro-Start bundle; this page uses the current product documents, and the custom option takes your own figure.
- Owens Corning, The Roofing Collection Product Guide (Pub. 10018857-J, April 2019) - TruDefinition Duration: 64 shingles, 3 bundles and 98.4 sq ft per square, 5 5/8 in exposure, 13 1/4 x 39 3/8 in. The same table lists 5 bundles per square for Berkshire and 6 for Woodmoor and Woodcrest, and the current Duration Premium page lists 4, so bundles per square depends on the line.
- Owens Corning DecoRidge Hip & Ridge and Starter Strip Plus product pages - DecoRidge: 30 pieces and 20 lineal feet per carton at 8 in exposure (8 in and 10 in sizes). Starter Strip Plus: 32 pieces and approximately 105 lineal feet per bundle (starter strip page: https://www.owenscorning.com/en-us/roofing/products/starter-strip).
- GAF, How Many Bundles of Shingles Are in a Square, and Owens Corning, DIY Roofing: Re-Roofing Tips (waste allowance) - Both makers say to add 10 to 15 percent to the material total for trim allowance and waste. GAF: a steep slope or rakes, valleys and dormers need more material than the square footage shows. Owens Corning: waste factors vary, and more complicated roofs have a higher waste factor (https://www.owenscorning.com/en-us/roofing/blog/diy-roofing). Neither splits the range by roof type: the 10 percent gable and 15 percent hip defaults here are this page's picks within it.
- Red X Apps, How to Calculate Rafter Length: Formula + Chart - The pitch multiplier sqrt(1 + (pitch/12)^2) (6/12 is 1.118) and roof area as plan area times the multiplier; 1,000 sq ft of plan at 6/12 is 1,118 sq ft of roof. The hip factor sqrt(2 + (rise/12)^2) is the steel square rafter table value, 20.78 in per foot of run at 12/12.
Limitations of this calculator
- This page counts material for one rectangular roof of one pitch, gable or hip. It is not a takeoff from a drawing. Valleys, dormers, chimneys, skylights, an L-shaped or T-shaped plan, a porch roof, a second layer and a tear-off are not figured; work each rectangle on its own and add the results.
- The waste allowance is yours. GAF and Owens Corning both say to add 10 to 15 percent for trim and waste. The 10 percent on a plain gable and 15 percent on a hip roof used here are this page's picks within that range, not a maker's split by roof type. Cut-up roofs, steep roofs and short runs need more.
- Bundles per square and the linear feet per bundle of starter and cap come from the makers' open data sheets for two lines (GAF Timberline HDZ, Owens Corning Duration) and change between lines, colors, regions and years. GAF's older Pro Field Guide prints 33 lin. ft. per Pro-Start bundle against 120.33 in the current product documents, so the label on the bundle decides. Check the manufacturer's label on the bundle you buy.
- Three bundles per square is the trade convention for 100 sq ft. The makers state 98.4 sq ft for 3 bundles, so the convention runs about 1.6 percent light. The page counts with the convention and, for the GAF and Owens Corning lines, shows the count at the maker's coverage next to it.
- Starter and cap are counted at their exact length and rounded up to whole bundles. No cut loss is added to them, and the cap is taken to the drip edge on hips and to the rake on the ridge.
- Underlayment, ice barrier, drip edge, nails, flashing, vents and sheathing are not counted. Pitch and slope limits, underlayment on low slopes, fastening on steep slopes and wind ratings come from the shingle installation instructions and the building code, not from this page.
- A gable ridge is taken parallel to the house length typed, and both slopes and all overhangs are alike. A hip roof has four slopes of one pitch, a common eave height and equal eave overhangs, and its ridge lies along the longer side.
- Values outside the field ranges are not accepted: house length 10 to 300 ft, width 8 to 150 ft, pitch 2/12 to 24/12, eave overhang 0 to 48 in, rake overhang 0 to 24 in, waste 0 to 40 percent. A zero or negative value is refused. This page does not figure rafter length (see the rafter length calculator), loads or member sizes.
Common mistakes when ordering shingles
- Ordering to the footprint. Shingles are bought by the sloped surface. A 40 x 30 ft house is 1,200 sq ft of footprint, but at 6/12 with 12 in overhangs the roof is 1,503 sq ft, about 303 sq ft more before any waste.
- Leaving out the overhangs. The roof extends past the walls. The same house with no overhang is 1,342 sq ft of roof, against 1,503 sq ft with 12 in at the eaves and rakes: about 161 sq ft, 5 bundles at this waste.
- Ordering with no waste. Cut pieces at the eaves, rakes, ridge and hips do not all get used. With 0 percent waste this roof is 46 bundles; with 10 percent it is 50. A roof with valleys and dormers needs more than 10 percent.
- Counting 3 bundles as exactly 100 sq ft. The makers state 98.4 sq ft for 3 bundles. At that coverage this roof needs 51 bundles, not 50. The waste allowance usually absorbs it, but at a low waste figure it can leave the roof one bundle short.
- Forgetting that starter and cap are separate products. Shingle bundles do not include the starter strip or the cap. This roof also needs 2 bundles of starter (155.6 ft of eave and rake) and 2 of hip and ridge cap (42.0 ft of ridge).
- Figuring cap for a hip roof along the ridge only. The 40 x 30 ft hip roof has a 10.0 ft ridge, but also four hips of 24.0 ft each. Cap for the ridge alone is 1 bundle; the full 106.0 ft is 5 bundles.
Common questions about shingle quantities
How do I calculate how many bundles of shingles I need?
Find the roof surface (footprint with overhangs times the pitch multiplier), divide by 100 for squares, add the waste, and multiply by the bundles per square. The default 40 x 30 ft gable at 6/12 is 1,503 sq ft, 15.03 squares, 16.53 with 10 percent waste, and at 3 bundles per square that is 50 bundles.
How many bundles are in a square of shingles?
A square is 100 sq ft of roof. GAF Timberline HDZ and Owens Corning Duration are packed 3 bundles per square, and the makers state 98.4 sq ft of coverage for those 3 bundles. Other lines differ: the Owens Corning guide lists 5 bundles per square for Berkshire and 6 for Woodmoor, and the current Duration Premium page lists 4. Check the label on the bundle.
How do I get the roof area from the footprint?
Add the overhangs to the footprint to get the plan area, then multiply by the pitch multiplier sqrt(1 + (rise/12)^2). 1,000 sq ft of plan at 6/12 is 1,118 sq ft of roof. This page does it for a gable or a hip roof: the default house is 1,344 sq ft of plan with its overhangs and 1,503 sq ft of roof.
How much waste should I add for shingles?
GAF and Owens Corning both say to add 10 to 15 percent for trim and waste, and more for a steep roof or one with valleys, hips and dormers. The page starts a plain gable at 10 percent and a hip roof at 15, and the field is yours. On the default roof, 0 percent is 46 bundles, 10 percent is 50, and the same house as a hip roof at 15 percent is 52.
How much starter strip do I need?
Starter goes along the eaves and, on a gable roof, usually the rakes. Take the total length and divide by what a bundle covers: GAF Pro-Start is 120.33 lin. ft. per bundle and Owens Corning Starter Strip Plus is about 105. The default roof has 155.6 ft of eave and rake, so 2 bundles of either.
How much ridge and hip cap do I need?
Measure the ridge and every hip, then divide by what a bundle covers: GAF Seal-A-Ridge is 25 lin. ft. per bundle and Owens Corning DecoRidge is 20 lin. ft. per carton. The gable ridge here is 42.0 ft, 2 bundles of Seal-A-Ridge or 3 of DecoRidge. A hip roof of the same size has a 10.0 ft ridge plus four hips of 24.0 ft, 106.0 ft in all.
Why does the page show a second bundle count at 98.4 sq ft?
The trade counts 3 bundles per 100 sq ft, but GAF and Owens Corning both state that 3 bundles cover 98.4 sq ft. The difference is about 1.6 percent. On the default roof it is 50 bundles by the convention and 51 at the stated coverage. When they differ, the waste allowance is the place to absorb it.
Does this calculator include underlayment, drip edge and nails?
No. It counts the field shingles, the starter strip and the hip and ridge cap for one rectangular roof. Underlayment, ice barrier, drip edge, nails, flashing and vents are counted separately, and valleys and dormers are not in the model. For the length of a rafter use the rafter length calculator.